for the Price of $140.00 Chrome Finish
for the Price of $160.00 Satin Nickel Finish
for the Price of $200.00 Gold Finish
Instuctions to Install and Use Your GoBidet Attachment
Note: Your new GoBidet system comes with the option to be installed as a cold water only system or a hot and cold water system. This unit is made to mont on both regular/round or elongated toilets.
Attachment to one-piece toilet
If you are installing a bidet system onto a one-piece toilet you will need to replace the support bracket on the unit with the longer support bracket # 2003-09.
1.) Firmly holding the bidet system body remove the 9/16" chrome nut located under the GoBidet label by unscrewing it with a 9/16" wrench.
2.) Simply replace with the longer support #2003-09 bracket and tighten 9/16" chrome nut.
Note: Some regular and one-piece toilets are fitted with French contour seat that will not allow your bidet system to perform properly.
Reminder: Keep your Regular or #2003-09 bracket for future use, should you need to change toilet.
4 in 1 Installation Instructions
1 Remove toilet seat
2 Center support bracket (G) on right side of toilet as shown. Insert bushing (C) through top and secure from bottom with plastic washer (D) and bronze nut (E) before completely tightening move shower arm (H) to it's maximum extension, moving the support bracket (G) until shower arm (H) is in the center of toilet. (on retracting - shower arm (H) should fall beneath toilet rim).
3 Once this is done finish tightening support bracket (G) in place.
4 Place plastic spacer (B) over left side opening as shown in Fig.1, and proceed to replace toilet seat cover back to its original place.
How to connect cold water line
Your GoBidet system brings already in place a 3/8" compression plug/screw ready for COLD water only installation (H inlet: As shown in Fig.2) Most homes have a valve/angle stop that supplies water to your toilet or vanity sink. Shut off valve/angle stop; then flush toilet completely and proceed to disconnect existing Flexible or pipe from the ballcock inlet at the bottom of the toilet tank. Firmly, (using Teflon tape if necessary) screw onto the ballcock "T" connector 2003.15, then place existing supply line back to its original connection. Connect 11" Flexible 2003.10 (3/8" male end) to the GoBidet open inlet and thereafter proceed to connect the female end of Flexible 2003.10 to the "T" connector 2003.15 (As shown on Fig.2)
How to connect hot water line
To use your bidet system with Hot and Cold water, you must remove the existing 3/8" plug (H inlet: as shown in fig.2) from the unit and proceed to connect a 3/8" male compression flexible hose (Not Included) to "H" inlet. (as shown in Fig.2)
Hot water connection can be obtained from the closest hot water source, (eg.:vanity sink, shower, heater). Proceed to follow installation instructions same as cold water connection. (See fig.2)
Note: Distances for hot water supply vary in all cases, therefore flexible hose for Hot water connection is not provided with the system.
How to use your personal hygiene system
(1) Once you are seated, with your right hand move lever (L) towards you, to position shower-head to the center of the toilet bowl. For better aim one can always move lever (L) back and forth to find a comfortable position.
(2) As shown in Fig.3 proceed VERY GENTLY to move knob/handle (K) backwards until you receive a soothing water pressure. By turning knob/handle (K) from side to side you can graduate the desired temperature (See Fig.4). For cold water wash only, you can position knob/handle to blue indicator side for permanently, and simply push back and forth to activate water flow.
(3) Once you feel freshly cleansed, turn off your bidet system by pushing knob/handle (K) forward as shown in Fig.3 Then proceed to move lever (L) back to the right to get shower head in its original position for future use.
